Engine Foxbody idle/throttle issues

[AeroCoupe]

So what is the motor craft plug number and which heads do you have again?

 

[red5.0fox]

So what is the motor craft plug number and which heads do you have again?

I’m not sure of the number. I have GT40 heads (not the P heads).

 

[red5.0fox]

Alrighty, I can confirm a new PCM solved all my issues. Crazy how that works.. Anyways, only things I have left are an exhaust leak I’m trying to fix and with these aftermarket headers, that’s proving to be a pita. I do have an oil leak inbetween the pan and the transmission. It’s very steady, and it’s keeping me from driving the car. Sound like a rear main? It isn’t an obvious pan leak, it looks more like it’s coming from directly inbetween.

 

[red5.0fox]

Here’s a photo for reference. This leak really only drips when the car is running, and it is really bad. Leaves a puddle every time. This is right between the oil pan and the flex plate

 

[General karthief]

Rear main or possibly leakage from the flywheel bolts, my money is on the seal.
just a guess though

 

[red5.0fox]

Rear main or possibly leakage from the flywheel bolts, my money is on the seal.
just a guess though

That’s where I’m putting my money aswell. Gonna get it pulled this weekend. Final piece of the puzzle and it’ll officially be fixed and ready to drive after 2.5 long years

 

[General karthief]

That’s where I’m putting my money aswell. Gonna get it pulled this weekend. Final piece of the puzzle and it’ll officially be fixed and ready to drive after 2.5 long years

that sentence was all wrong, here, let me correct it..... "that will officially be fixed and ready to drive till the next thing breaks"........
You're welcome.

 

[red5.0fox]

that sentence was all wrong, here, let me correct it..... "that will officially be fixed and ready to drive till the next thing breaks"........
You're welcome.

We are going to pretend that this autocross event I plan on attending will not cause any issues to the car my wallet needs to enjoy fantasy land for a little bit

 

[AeroCoupe]

Check the back of the lower intake and make sure its not leaking there and running down the back of the block. Not super likely and my bet would also be on the rear main.

 

[Mindseye007]

I’ve tried clocking them in the past and haven’t had any luck, I’ll try it again tomorrow when I get it put back together. There’s been a nasty vacuum leak coming from somewhere towards my lower intake. My smoke machine couldn’t find it but that’s where it sounds like it’s coming from. I’m taking it apart down to there and I’m gonna put it back together and see if the leak disappears.

What is the best option to do a smoke test on the exhaust just put the tip in the tailpipe and wrap a Rag to keep the smoke in ?

 

[Mindseye007]

I’ve tried clocking them in the past and haven’t had any luck, I’ll try it again tomorrow when I get it put back together. There’s been a nasty vacuum leak coming from somewhere towards my lower intake. My smoke machine couldn’t find it but that’s where it sounds like it’s coming from. I’m taking it apart down to there and I’m gonna put it back together and see if the leak disappears.

What is the best option to do a smoke test on the exhaust just pit the tip in the tailpipe and wrap a Rag to keep the smoke in ?

Yes but not in regards to the BBK throttle body. Too many have experienced the dreaded BBK whistle.

Yes I heard a lot about that dreaded BBK whistle to so I stayed away and installed a 70 mm accufab throttle body. No problems at all.

 

[Mindseye007]

I’ve tried clocking them in the past and haven’t had any luck, I’ll try it again tomorrow when I get it put back together. There’s been a nasty vacuum leak coming from somewhere towards my lower intake. My smoke machine couldn’t find it but that’s where it sounds like it’s coming from. I’m taking it apart down to there and I’m gonna put it back together and see if the leak disappears.

What is the best option to do a smoke test on the exhaust just pit the tip in the tailpipe and wrap a Rag to keep the smoke in ?

Yes but not in regards to the BBK throttle body. Too many have experienced the dreaded BBK whistle.

Yes I heard a lot about that dreaded BBK whistle to so I stayed away and installed a 70 mm accufab throttle body. No problems at all.

The only vacuum that goes into the reservoir in the passenger fender connects to the solenoids and the EGR valve itself. There is no vacuum going anywhere else from it.

If the smog pipe that goes to the back of the heads is it easy clean the carbon out? or is it just better to order a new one from LMR? and install it? I'm getting thermactor codes and I think it is cuz the smog pipe Is plugged up. Changed my EGR Valve and it was plugged solid installed a new one I am getting better gas milage now.